Hantle ATM Error Codes

Code Description Remedy
20001 Unable to load a cassette Remove and replace cassette – Check the micro-switch located on the inside left wall of the dispenser
20002 Low Cash Replenish the cash – if using less than 75 bills, disable “Low Cash Warning” in the Transaction Setup menu.
20003 Reject Bin is Full Empty reject bin – if bin is empty, do a Cassette Total
20004 Vault Door is Open Close vault door – check vault door switch (located upper left corner) – check that black and white, 2 -wire connector is properly connected at rear of main board.
20010 Receipt Paper Jam Remove jammed paper – Release receipt paper drawer by pressing the tab with the green sticker located at the front of the printer.
20012 Receipt printer feed lever open Close the feed lever on the printer.
20013 Receipt paper is empty Replenish the paper roll
20014 Thermal printer is overheated Contact manufacturer
2xx15 Cash Dispenser detects bills prior to dispensing Remove any jammed bills from the dispenser.
Axxx1 Receipt printer feed lever open – during operation Close the feed lever on the printer.
Axxx2 Thermal printer is overheated – during operation Contact manufacturer
Axxx3 Receipt Paper Jam Remove jammed paper – Release receipt paper drawer by pressing the tab with the green sticker located at the front of the printer.
Axxx4 Receipt paper is empty Replenish the paper roll
Axxx5 Receipt paper is jamming during loading Remove any jammed paper and then reload.
Axxx8 Receipt paper cutter error Contact manufacturer
ADNxx Printer connection error Check cables between Printer and Mainboard, remove cables (even though they may be attached) and re-connect
C001x CDU sensor is tripped Most typically a COO11 error, this would indicate a bill jam at the exit sensor of the Cash Dispenser. Usually caused by a customer putting fingers in the cash drawer during dispense.
C002x CDU sensor is tripped Check dispenser for jammed bills and restart the machine
C0030 CDU motor failure Contact manufacturer
C0031 CDU Gate solenoid error Contact manufacturer
C0032 Outlet solenoid error Contact manufacturer
C0033 CDU Encoder error Contact manufacturer
C0034 Double Note detect module failure Contact manufacturer
C0035 Double Note detect module failure (2) Contact manufacturer
C0036 Detected notes in path before initializing Check for notes in the Cash Dispenser.
C0039 Gate sensor open during initializing Contact manufacturer
C003B Notes detected during installation Check for notes in the Cash Dispenser.
C0040 Cassette removed during dispense Reset the cassette, check position of microswitch on right rear wall of cassette bay in the dispenser. Check the condition of the white plastic cassette retaining clips in the dispenser.
C0041 Tried to dispense notes more than 5 times Check the condition of the cash in the cassette. Verify that the cash is of good quality. Check that the denomination in Transaction setup matches the actual denomination loaded
C0042 Note jam Check for notes in the Cash Dispenser.
C0043 More than 10 notes rejected during one transaction Verify the quality of the cash. Straighten and shuffle cash in the cassette.
C0044 More than 5 notes rejected consecutively Verify the quality of the cash. Straighten and shuffle cash in the cassette.
C0046 CDU Hardware Failure Contact manufacturer
C0047 Feed error Check the notes in the cassette, feed error occurred where the cash leaves the cassette. Verify that the cassette has cash in it.
C0048 Incorrect bill count Verify cash count under settlement
C004A Jammed notes Check for notes in the Cash Dispenser.
C004B Long note detected 3 times consecutively Verify the quality of the cash. Straighten and shuffle cash in the cassette.
C004C Miscount of notes between sensors Verify operation of exit gate. Check the number of dispensed notes.
C004D Cash cassette not properly set Reset the cassette, check position of microswitch on right rear wall of cassette bay in the dispenser. Check the condition of the white plastic cassette retaining clips in the dispenser.
C004E Miscount of notes between sensors Test CDU using diagnostics, verify amount of dispensed notes versus requested notes.
C004F Miscount of notes between sensors Test CDU using diagnostics, verify amount of dispensed notes versus requested notes.
C0050 Power failure during dispense Remove any notes from path, verify amount of dispensed notes.
C0051 Over 150 notes requested Contact manufacturer
C0052 Detected notes in path after dispense Remove any notes from path, verify amount of dispensed notes.
C0053 CDU double detect module failure. Contact manufacturer
C0055 Detected long notes at outlet sensor Check quality of cash, verify that denomination matches actual loaded cash.
C0056 Exit gate sensor failure Contact manufacturer
C006x Sensor failure Check sensors for debris. Contact manufacturer.
C007x Sensor failure Check sensors for debris. Contact manufacturer.
C0082 Shutter failure Contact manufacturer
C0083 Stacker sensor failure Contact manufacturer
C0084 Shutter close error Contact manufacturer
CDNxx CDU connection failure Check cables between CDU and Mainboard, remove cables (even though they may be attached) and re-connect. This error is of concern only if it is repeated. Outside interference may cause it.
D0001 Modem initializing error Check modem
D0002 Reversal transaction failed. Check transaction with the processor. Verify CDU functionality with diagnostics. Verify phone connection.
D0012 Invalid Transaction Code reported from host processor
D0013 Invalid Amount Code reported from host processor
D0014 Invalid Card Number Code reported from host processor
D0020 Surcharge screen should have been displayed Code reported from host processor
D0024 Exceeds issuer withdrawl limit Code reported from host processor
D0039 No credit account Code reported from host processor
D0051 Insufficient funds Code reported from host processor
D0052 No checking account Code reported from host processor
D0053 No savings account Code reported from host processor
D0054 Expired Card Code reported from host processor
D0055 Invalid PIN Code reported from host processor – If processing through Coredata verify that Dual-Masterkey is enabled (Host Setup) – all other processors it is disabled.
D0057 Transaction not permitted – card Code reported from host processor
D0058 Transaction not permitted – Terminal Code reported from host processor
D0061 Exceeded withdrawl limit Code reported from host processor
D0075 Number of PIN tries exceeded Code reported from host processor
D0078 No Account Code reported from host processor
D0080 Invalid Date Code reported from host processor
D0083 Cannot verify PIN Code reported from host processor
D0086 Cannot verify PIN Code reported from host processor
D0091 Bank unavailable Code reported from host processor
D0092 System unavailable Code reported from host processor
D0093 Transaction serial number mismatch Contact host processor
D0094 Record format mismatch Contact host processor
D0095 Routing ID mismatch Verify Routing ID number – Contact host processor
D0096 Terminal ID mismatch Verify Terminal ID number – Contact host processor
D0097 Response type mismatch (reversal) Contact host processor
D0098 Response type mismatch (day-close) Contact host processor
D0099 Response type mismatch (Configuration) Contact host processor
D009A Response type mismatch (Withdrawl, Balance, Transfer) Contact host processor
D009B STX omitted Contact host processor
D009C ETX omitted Contact host processor
D009D FS omitted (after response code) Verify that version of Mini-Bank Software matches host processor. Contact host processor
D009E FS omitted (after retrieval referance number) Verify that version of Mini-Bank Software matches host processor. Contact host processor
D009F FS omitted (after system trace audit number) Verify that version of Mini-Bank Software matches host processor. Contact host processor
D00A0 FS omitted (after account balance) Verify that version of Mini-Bank Software matches host processor. Contact host processor
D00A1 FS omitted (after available balance) Verify that version of Mini-Bank Software matches host processor. Contact host processor
D00A2 FS omitted (after available balance) Verify that version of Mini-Bank Software matches host processor. Contact host processor
D00A3 FS omitted (after authorization response text) Verify that version of Mini-Bank Software matches host processor. Contact host processor
D00A4 ETX is in wrong place Verify that version of Mini-Bank Software matches host processor. Contact host processor
D00A5 FS omitted (after total cash dispense amount in day close) Verify that version of Mini-Bank Software matches host processor. Contact host processor
D00A6 FS omitted (after total non cash dispense amount in day close) Verify that version of Mini-Bank Software matches host processor. Contact host processor
D00A7 FS omitted (after surcharge amount in day close message) Verify that version of Mini-Bank Software matches host processor. Contact host processor
D00A8 FS omitted (after surcharge amount in configuration message) Verify that version of Mini-Bank Software matches host processor. Contact host processor
D00A9 ETX omitted (from configuration message) Contact host processor
D0300 Modem is not responding Verify modem function.
D1000 No Connection Verify modem function.
D1100 ENQ not received from host Contact host processor
D1200 Transmission error Verify modem function.
D1300 NAK sent 3 times to host Verify host phone number – See D170x
D1500 Modem connection time out – host not responding Verify host phone number – verify modem speed – See D170x
D170x Modem cannot support connection – excessive line noise (usualy D1704/06) Phone line connected to ATM will not support Data-communication. In line filter may fix this. Excessive EMI emissions from outside source (neon sign, freezer)
D1800 No dial tone Verify that incoming phone line is plugged into “Line” rather than “Phone” on mainboard. Phone line is in use or is being shared with another phone device (FAX, POS, phone)
D1900 No answer Verify host phone number – See D170x
D2000 Phone line Busy Verify host phone number – call line with handset and check for busy signal – See D170x
D2100 Modem initializing error Check modem
D2200 EOT not received from host Contact host processor
E000x RMS port failure, response time out, modem failure, no dial tone Verify RMS settings (Host Setup) – See D170x
F0001 Current Number of Bills is 0 Load notes into the cash cassette – use Add Cassette function in Settlement
F0002 No Surcharge Owner set Set Surcharge owner – (Customer Setup)
F0003 No Surcharge Amount Set Surcharge amount – (Customer Setup)
F0004 No refresh timer set when advertisement is enabled Set refresh timer – (Customer Setup)
F0005 No Advertisement text when advertisement is enabled Set Advertisement text – (Customer Setup)
F0006 Dispense limit set error (must be less than 25 notes) Set Dispense limit – (Transaction Setup)
F0007 Denomination Set error Valid Denominations are $10, $20, $50, $100 – (Transaction Setup)
F0008 Fast Cash Set error (cannot exceed dispense limit) Check fast cash settings (Transaction Setup)
F0009 Master Key index is invalid Check Master Key index – verify checksum (Host Setup)
F000A Master Key is empty Check Master Key checksum – re-inject key (Host Setup)
F000B Host Telephone Number is not set Set Host Telephone Number – (Host Setup)
F000C Error Retry timer is not set Set Error retry timer (Host Setup)
F000D RMS Password is not set when RMS is enabled Set RMS Password – (Host Setup)
F000E RMS phone number is not set when RMS send is enabled Set RMS Phone number – (Host Setup)
F000F Terminal ID is not set Set Terminal ID number – (Host Setup)
F0010 Routing ID is not set Set Routing ID number – (Host Setup)
F0011 Master Key Serial number is not set Set Master Key serial number – (Host Setup)